Voltage output

    Data acquisition unit to measure the selected signal on demand

    1) Modules allow wide range of measurements

    Able to use for wide range of applications in various measurement scenes by extended different type of input module

     

    2) Extending modules

    Allow to make various measurements according to the purpose by adding the units corresponding to the measurement signals

     

    3) Touch panel system

    Intuitive operation by using touch panel. Also able to operate with cursor keys with the same feeling as the midi LOGGER GL series

     

    4) Supports multiple storage

    Equipped various data collection methods and network functions to be adapted for variety of measurements applications

    Category:
      Description

      GL7000 specifications

      Item Description
      Model number GL7000
      Number of module Attached to up to 10 modules (*1)
      Number of input channels Max. 112 channels in 1 of GL7000
      External Input/Output signals (*2) Input Start/Stop, External trigger, External sampling, Auto balance (*3)
      Signal type: Contact (relay), Open collector, Voltage
      Output Trigger, Busy (*3), Alarm (10 channels) (*4)
      Signal type: Open collector (pulled-up by resistor 10 kΩ)
      Trigger, Alarm function Trigger action Start or stop capturing data by the trigger
      Trigger repeat Enabled (ON): Automatically re-armed for the next data capture function
      Disabled (OFF): Data capture is completed in a single trigger
      (Hold off repeat action in specified period: Previous start to next start, previous stop to next start)
      Trigger source Start: Off, Measured signal, Alarm, External signal, Clock, Week or Time
      Stop: Off, Measured signal, Alarm, External signal, Clock, Week or Time
      Trigger determination conditions for measured signal Combination: OR or AND condition at the level of signal or edge of signal
      Analog: Higher/Rising, Lower/Falling, Window-in, Window-out
      Logic (*5): Higher/Rising, Lower/Falling
      Pulse (*5): Higher/Rising, Lower/Falling, Window-in, Window-out
      Alarm determination condition (*6) Combination: OR or AND condition at the level of signal or edge of signal
      Analog: Higher/Rising, Lower/Falling, Window-in, Window-out
      Logic (*5): Higher/Rising, Lower/Falling
      Pulse (*5): Higher/Rising, Lower/Falling, Window-in, Window-out
      Alarm output 10 channels
      Pre-trigger (*7) Number of data before trigger: Up to specified number of captured data
      Calculation function Between channels Addition, Subtraction, Multiplication and Division for two analog inputs (Sampling speed is limited up to 10 Samples/s (100 ms interval). Available arithmetic element and the output destination is the analog input channel 1 to 100.)
      Statistical Select two calculations from Average, Peak, Max., Min. in real time and replay (*8)
      Move function of the display range Beginning, center or end of the data, Trigger point, Specific time (absolute, relative), Call cursor
      Search function Search for analog signal levels, logic signal pattern, pulse signal levels or alarm point in captured data
      Annotation function Comment can be set in each channel (up to 31 alphanumeric characters)
      Message / Marker Functions Message: The registered messages or entered message is able to be recorded for any timing. Up to 8 messages can be pre-registered.
      Marker: Marker is able to record for occurring alarm or power failure.
      Resume Resume automatically in the same condition after power is recovered as when the power failure occurred during data capture. (*9)
      FFT analysis function
      (Firmware ver. 1.20 or later)      		 Analyzing frequency range 0.08, 0.2, 0.4, 0.8, 1.6, 2, 3.2, 4, 8, 20, 40, 80, 200, 400, 800 Hz, 2, 4, 8, 20, 40, 80, 200, 400 kHz
      Number of points 500, 1000, 2000, 4000, 10000
      Window function Rectangular, Hanning, Hamming, Blackman, Flat-top, Exponential
      Averaging Summation average, Exponential average, Peak hold
      Channels 4 channels
      Functions Y-T, Linear, Power, PSD, Cross, Transfer function, Coherence, COP
      Display mode Single display, Dual display, Nyquist
      Interface to PC Ethernet (10 BASE-T/100 BASE-TX), USB 2.0 (High speed)
      Network function WEB server, FTP server, FTP client, NTP client, DHCP client
      USB drive mode Emulate the USB memory device (*10)
      Storage device Built-in RAM (2 million samples, built-in amplifier module),
      Flash memory (4 GB, built-in the main module) (*12)
      External (*11) SD card (Support SDHC, up to 32GB) slot, SSD (Approx. 128GB (*12))
      The file for capturing data is limited up to 4GB. (*13)
      Data saving function Sampling speed (interval) 1 MS/S(1 million samples per second) to 1S/h (1 sample per hour), and synchronized with external sampling signal
      (Interval: 1, 2, 5, 10, 20, 50, 100, 200, 500 µs, 1, 2, 5, 10, 20, 50, 100, 200, 500 ms, 1, 2, 5, 10, 20, 30, 1, 2, 5, 10, 20, 30 min, 1 hur)
      * The maximum sapling speed (minimum sampling interval) is different depending on the type of module.
      * Sampling can be set up to the fastest speed among multiple type connected modules. If the set sampling speed exceeds the fastest speed on module, signal will be sampled and updated at the highest speed of its module and the previous data will be used until the data is updated.
      * The maximum sampling speed (minimum sampling interval) varies depending on the specified recording destination.
      Built-in RAM: up to 1 MS/s (1 µs interval)
      SSD module: up to 500 kS/s (2 µs interval) at 1 or 2 modules installed, up to 200 kS/s (5 µs interval) at 3 or 4 modules installed, up to 1 kS/s (1 ms interval) at 5 or 10 modules installed
      Built-in Flash memory: up to 1 MS/s (1 µs interval)
      External SD Flash memory: up to 1 kS/s (1 ms interval)
      Captured data (*11) Built-in RAM, Built-in Flash, SD memory card, SSD (Data is saved directly to it.)
      Data in built-in RAM Specified number of data up 2 million samples in increments of 1
      Auto save (*11) Available for the built-in RAM
      Enabled (ON): Data in the RAM is saved automatically to the built-in Flash, SD memory card, SSD
      Disabled (OFF): Data in the RAM is not maintained after power is turned off
      Capturing mode (*11) Mode: Off, Normal, Ring, Relay
      Ring (*14): Saved most recent data (Number of capturing data: 1000 to 2000000 points, Destination of data: Built-in RAM, Built-in Flash, SD memory card, SSD)
      Relay(*13)(*15): Saved data to multiple file without losing data until capturing data is stopped (Destination of data: Built-in Flash, SD memory card, SSD)
      During data capture (*17) Displaying information in two windows, Hot-swapping the SD memory card, Saving data in between cursors.
      Backup (*11) Backup interval (*18): Off, 1, 2, 6, 12, 24 hrs.
      Data destination (*18): SD memory card, SSD, FTP server
      Data format (*18): GBD (binary) or CSV (test)
      Data destination for backup cannot be specified to the same storage for destination of capturing data.
      Dual sampling function (*19) It enables to record signal with two sampling speed. While the signal is recorded with low speed sampling for long term recording, the transient part is recorded with high speed sampling after the trigger occurs.
      Current (low-speed) sampling
      Recording media：Built-in flash memory or SD card
      Sampling interval：1, 2, 5, 10, 20, 50, 100, 125, 200, 250, 500ms, 1, 2, 5, 10, 20, 30s, 1, 2, 5, 10, 20, 30min, 1h
      Trigger timer feature: Starting time, Stopping time, Repeat recording
      Event (high-speed) sampling
      Recording media：Built-in RAM or SSD (optional)
      Sampling interval： 1, 2, 5, 10, 20, 50, 100, 200, 500us
      Engineering Scale function Measured value can be converted to the engineering unit
      Analog voltage: Converts by four reference points (gain, offset)
      Temperature: Converts by two reference points (offset)
      Pulse count: Converts by two reference points (gain)
      Synchronization between units Start and Trigger (*16)
      Accuracy of clock (at 23°C) ±0.002% (Monthly deviation approx. 50 sec.)
      Operating environment 0 to 40°C, 5 to 85% RH (non condensed)
      Power source 100 to 240 V AC, 50 to 60Hz
      Power consumption 110VA
      Standard accessories Quick guide, CD-ROM, AC power cable
      External dimensions (W x D x H) Main module: Approx. 193 x 141 x 160 mm (Excluding Projection),
      Alarm output terminal: Approx. 30 x 136 x 145 mm (Excluding projection)
      Weight Main module: Approx. 2.2 kg, Alarm output terminal: Approx. 350 g