Phone

+603-5621 5786

Business Hour

08:30 - 17:30

TES Digital DC/AC Clamp Meter TES-3050H

TES-3050H
Digital DC/AC Clamp Meter
Product Features
  • 3-3/4 Digital LCD with bar-graph.
  • Auto-Ranging on Volt, Ohm, Current,
  • Frequency measurements.
  • Auto-power off.
  • Data Hold mode.
  • MAX/MIN Hold mode.
  • Zero Adjustment/Relative Reading.
  • PEAK Hold mode.
    (only ACV and ACA Range)

Description

 MEASUREMENT SPECIFICATIONS

DC Current (Autorange & Manual)

Range Resolution Accuracy Overload protection
400A 0.1A ±(2% + 5) 1100A
1000A 1A

 Response time: 5 seconds max. to rated accuracy within selected range.

 

AC Current (Autorange & Manual): Low Pass Filter

Range Resolution Accuracy Overload protection Frequency Response
400A 0.1A ±(2% + 10) 1100A 40400 Hz
1000A 1A

 Conversion type: AC coupled,TRMS measurement.

 Additional Crest Factor Errors (non – sinecure)

Crest Factor Error (% of reading)
1 – 3 0.5%
3 – 5 3%
5 – 7 6%

 Response time: 5 seconds max, to rated accuracy within selected range.

 

INFLUENCE OUANTITY
Influence quantity Limits of variation Measured quantity Tolerance
Position of conductor in the clamp conductor’s diameter: 20mm In relation to the center Amps ±(1%+5)

 

 DC Voltage (Autorange & Manual)

Range Resolution Accuracy Input Impedance Overload protection
400mV 0.1mV   ≒ 11MΩ 600Vrms
4V 0.001V ±(0.75% + 2) ≒ 10MΩ
40V 0.01V
400V 0.1V
600V 1V

 Response time: 3 seconds max. to rated accuracy within selected range.

 

AC Voltage (Autorange & Manual): Low Pass Filter 

Range Resolution Accuracy Input impedance Overload protection Frequency Response
50~60Hz 400Hz
4V 0.001V ±(1.2% +5) ±(2.5% +10) ≒11MΩ 600Vrms 40 400 Hz
40V 0.01V ≒10MΩ
400V 0.1V
600V 1V ±(1.5% +5) ±(3% +10)

 Conversion type: AC coupled,TRMS measurement.

 Additional Crest Factor Errors (non – sinecure)

Crest Factor Error (% of reading)
1 – 3 0.5%
3 – 5 3%
5 – 7 6%

 Response time: 5 seconds max, to rated accuracy within selected range.

 

Frequency (Hz) (Autorange for Voltage)

Range Resolution Accuracy Sensitivity Overload protection
100Hz 0.01Hz ±(0.1% + 2) 100mV 600Vrms
1KHz 0.1Hz
5KHz 0.001KHz

 

Frequency (Hz) (Autorange for Current)

 

Range Resolution Accuracy Sensitivity Overload protection
100Hz 0.01Hz ±(0.5% + 5) 5A 1100A
1KHz 0.1Hz

 

Resistance (Ω) (Autorange & Manual)

Range Resolution Accuracy Open circuit Voltage Overload protection
400Ω 0.1Ω ±(1% + 5) ≦ 0.5 VDC 600Vrms
4KΩ 0.001KΩ ±(1% + 3)
40KΩ 0.01KΩ
400KΩ 0.1KΩ
4MΩ 0.001MΩ
40MΩ 0.01MΩ ±(1.5% + 3)

 

Audible continuity

Range Continuity beeper Open Circuit Voltage Overload  protection
≦ 40Ω ≦ 0.5V 600Vrms

 

Diode test

Range Resolution Accuracy Overload protection
 2.000V 0.001V ±(1%+2) 600Vrms

 Max. open circuit Voltage: 3.2V

 Max. short circuit Current: 1.0mA (typical).

 Peak Hold Specifications

 

AC Voltage (Manual Range): Low Pass Filter

Range Resolution Accuracy
(50Hz60Hz)
Input Impedance Overload protection
4V 0.001V ±(2.5% + 10) ≒ 11MΩ 600Vrms
40V 0.01V ≒ 10MΩ
400V 0.1V
600V 1V

 

AC Current (Manual Range): Low Pass Filter

Range Resolution Accuracy
(50Hz60Hz)
Overload protection
400A 0.1A ±(2.5 % + 10) 1100A
1000A 1A

 

Peak Detect Acquisitions Time100ms

 

Peak Hold: storage of the peak value.

 SPECIFICATIONS:

  Numerical Display            3-3/4 digit liquid crystaldisplay (LCD) maximum reading 3999.

  Range Selection               All ranges are selected  by a single range switch.

  Over Range Indication       :LCD will show a “OL” flashing in the highest position

                                             accompanied with a continuous beeping.

                                              (except for ranges of 1000A AC/DC, and 600VDC 600VAC ).

 Low Battery Indication        :The  is displayed when the battery voltage drops below

                                              the operating voltage.

  Sampling Rate                  20 times/sec ( Barograph )    2 times/secDigital Display

  Power Source                   one 006p 9V or IEC 6F22  or NEDA 1604 Battery.

  Battery Life                        100hr approx. (Alkaline)

  Polarity                              Automatic polarity ” ”  display for negative input.

  Auto power off time           Approx. 30 minutes 

  Operating Temperature       :0°C to 50°C(32°F to 122°F)  and Humidity  below 80%RH     

  Storage Temperature          :-10°C to 60°C(14°F to 140°F)   and Humidity below 70%RH     

  Dimensions                         :239(L)×66(W)×34(H)mm

  Weight                                 :Approx. 430g 

 Accessories                         :Instruction manual, Battery, Test leads,Carry Case.

Ready to Transform Your Business? Contact Us Today

Categories

Request a Quote or Further Information

Please fill in the request form below and one of our engineers will contact you to discuss your system requirements and if we can help, our typical response time is within 1 – 3 working day.